• ce qui manque a LUCI : explorateur de fichier (file editor)
• a installer :
  • panel maison
  • backdoor terminal
  • webcam

notes

• http://wiki.openwrt.org/doc/howto/luci.essentials mod_simple_vhost ?

recuperé dans kernel log WL500Gp : Oct 31 19:35:09 (none) user.info kernel: hub.c: new USB device 01:03.0-2, assigned address 7 connexion webcam Oct 31 19:35:09 (none) user.warn kernel: usb.c: USB device 7 (vend/prod 0x46d/0x8ad) is not claimed by any active driver. connexion webcam gspca_zc3xx 046d:08ad Logitech QCCommunicate STX

• opkg install : kmod-usb2 , kmod-video-gspca-zc3xx , mjpg-streamer
• dans /etc/init.d/ changer input_uvc.so par input_gspcav1.so ajouter -w /www/webcam_www à output_http.so
  • could't set video palette Abort : https://forum.openwrt.org/viewtopic.php?id=27644
• on va donc tenter fswebcam avec libv4l (a installer)
  • export LD_PRELOAD=/usr/lib/libv4l/v4l2convert.so
  • fswebcam -v -r 640×480 -F 2 -S 1 /tmp/out.jpg

fswebcam -v -r 640x480 -F 2 -S 1 /tmp/out.jpg
--- Opening /dev/video0...
Trying source module v4l2...
/dev/video0 opened.
src_v4l2_get_capability,83: /dev/video0 information:
src_v4l2_get_capability,84: cap.driver: "zc3xx"
src_v4l2_get_capability,85: cap.card: "USB Camera (046d:08ad)"
src_v4l2_get_capability,86: cap.bus_info: "usb-ar71xx-ehci-1"
src_v4l2_get_capability,87: cap.capabilities=0x05000001
src_v4l2_get_capability,88: - VIDEO_CAPTURE
src_v4l2_get_capability,97: - READWRITE
src_v4l2_get_capability,99: - STREAMING
No input was specified, using the first.
src_v4l2_set_input,177: /dev/video0: Input 0 information:
src_v4l2_set_input,178: name = "zc3xx"
src_v4l2_set_input,179: type = 00000002
src_v4l2_set_input,181: - CAMERA
src_v4l2_set_input,182: audioset = 00000000
src_v4l2_set_input,183: tuner = 00000000
src_v4l2_set_input,184: status = 00000000
src_v4l2_set_pix_format,537: Device offers the following V4L2 pixel formats:
src_v4l2_set_pix_format,550: 0: [0x4745504A] 'JPEG' (JPEG)
src_v4l2_set_pix_format,550: 1: [0x33424752] 'RGB3' (RGB3)
src_v4l2_set_pix_format,550: 2: [0x33524742] 'BGR3' (BGR3)
src_v4l2_set_pix_format,550: 3: [0x32315559] 'YU12' (YU12)
src_v4l2_set_pix_format,550: 4: [0x32315659] 'YV12' (YV12)
Using palette JPEG
src_v4l2_set_mmap,689: mmap information:
src_v4l2_set_mmap,690: frames=4
src_v4l2_set_mmap,737: 0 length=118784
src_v4l2_set_mmap,737: 1 length=118784
src_v4l2_set_mmap,737: 2 length=118784
src_v4l2_set_mmap,737: 3 length=118784
--- Capturing 2 frames...
Skipping frame...
Capturing 2 frames...
Captured 3 frames in 0.26 seconds. (11 fps)
--- Processing captured image...
Unable to load font 'luxisr': libgd was not built with FreeType font support

Disabling the the banner.
Writing JPEG image to '/tmp/out.jpg'.

• opkg install : motion : ca fonctionne très bien le fichier de .conf

lien de support :

• http://wiki.openwrt.org/doc/howto/usb.video
• http://www.ideasonboard.org/uvc/
• http://linuxtv.org/wiki/index.php/Gspca ⇒ gspca_zc3xx 046d:08ad Logitech QCCommunicate STX
• http://www.jopa.fr/index.php/2008/11/01/openwrt-et-webcam-usb-streaming-wifi/
• http://www.jopa.fr/index.php/2008/11/06/openwrt-et-webcam-2eme-partie-video-surveillance-avec-motion/
• https://forum.openwrt.org/viewtopic.php?pid=100651
• http://mjpg-streamer.svn.sourceforge.net/viewvc/mjpg-streamer/mjpg-streamer/

hub.c: new USB device 01:03.0-2, assigned address 3 usb.c: USB device 3 (vend/prod 0x46d/0x8f6) is not claimed by any active driver. http://simaten.free.fr/wiki/tiki-view_blog_post.php?postId=123

gspca_zc3xx 046d:08da Logitech QuickCam Messenger gspca_stv06xx 046d:0840 QuickCam Express

le Buffalo ne dit rien sur l'id de la webcam: Dec 28 19:15:08 Buffalo user.info kernel: usb 1-1: new full speed USB device using ar71xx-ehci and address 3 Dec 28 19:15:08 Buffalo user.info kernel: usb 1-1: configuration #1 chosen from 1 choice Dec 28 19:18:12 Buffalo user.info kernel: usb 1-1: USB disconnect, address 3

fswebcam -v -r 640×480 -F 2 -S 1 /tmp/out.jpg
--- Opening /dev/video0...
Trying source module v4l2...
/dev/video0 opened.
src_v4l2_get_capability,83: /dev/video0 information:
src_v4l2_get_capability,84: cap.driver: "STV06xx"
src_v4l2_get_capability,85: cap.card: "Camera"
src_v4l2_get_capability,86: cap.bus_info: "usb-ar71xx-ehci-1"
src_v4l2_get_capability,87: cap.capabilities=0x05000001
src_v4l2_get_capability,88: - VIDEO_CAPTURE
src_v4l2_get_capability,97: - READWRITE
src_v4l2_get_capability,99: - STREAMING
No input was specified, using the first.
src_v4l2_set_input,177: /dev/video0: Input 0 information:
src_v4l2_set_input,178: name = "STV06xx"
src_v4l2_set_input,179: type = 00000002
src_v4l2_set_input,181: - CAMERA
src_v4l2_set_input,182: audioset = 00000000
src_v4l2_set_input,183: tuner = 00000000
src_v4l2_set_input,184: status = 00000000
src_v4l2_set_pix_format,537: Device offers the following V4L2 pixel formats:
src_v4l2_set_pix_format,550: 0: [0x47425247] 'GRBG' (GRBG)
Using palette SGRBG8
Adjusting resolution from 640x-1 to 324x240.
src_v4l2_set_mmap,689: mmap information:
src_v4l2_set_mmap,690: frames=4
src_v4l2_set_mmap,737: 0 length=81920
src_v4l2_set_mmap,737: 1 length=81920
src_v4l2_set_mmap,737: 2 length=81920
src_v4l2_set_mmap,737: 3 length=81920
--- Capturing 2 frames...
Skipping frame...
Capturing 2 frames...
Captured 3 frames in 0.22 seconds. (13 fps)
--- Processing captured image...
Unable to load font 'luxisr': libgd was not built with FreeType font support

Disabling the the banner.
Writing JPEG image to '/tmp/out.jpg'.

Jan 12 21:45:30 Buffalo user.err syslog: [1] Unable to find a compatible palette format. Jan 12 21:45:30 Buffalo user.debug syslog: [1] Using VIDEO_PALETTE_YUV420P palette Jan 12 21:45:31 Buffalo user.err syslog: [1] sync error in proc 1619: Invalid argument Jan 12 21:45:32 Buffalo user.err syslog: [1] mcapture error in proc 1619: Invalid argument Jan 12 21:45:32 Buffalo user.err syslog: [1] Video device fatal error - Closing video device

LD_PRELOAD=/usr/lib/libv4l/v4l1compat.so /usr/bin/motion [0] Processing thread 0 - config file /etc/motion.conf [0] Motion 3.2.11.1 Started [0] Thread 1 is from /etc/motion.conf [1] Thread 1 started [1] cap.driver: “STV06xx” [1] cap.card: “Camera” [1] cap.bus_info: “usb-ar71xx-ehci-1” [1] cap.capabilities=0x05000001 [1] - VIDEO_CAPTURE [0] motion-httpd/3.2.11.1 running, accepting connections [0] motion-httpd: waiting for data on port TCP 8080 [1] - READWRITE [1] - STREAMING [1] Supported palettes: [1] 0: RGB3 (RGB3) [1] 1: BGR3 (BGR3) [1] 2: YU12 (YU12) [1] Selected palette YU12 [1] index_format 8 Test palette YU12 (320×240) [1] Using palette YU12 (320×240) bytesperlines 320 sizeimage 115200 colorspace 00000008 [1] found control 0x00980900, “Brightness”, range 0,31 [1] “Brightness”, default 3, current 3 [1] found control 0x00980901, “Contrast”, range 0,15 [1] “Contrast”, default 11, current 11 [1] found control 0x00980910, “Gamma (software)”, range 500,3000 [1] “Gamma (software)”, default 1000, current 1000 [1] found control 0x00980911, “Exposure”, range 0,1023 [1] “Exposure”, default 256, current 256 [1] found control 0x00980912, “Auto Gain (software)”, range 0,1 [1] “Auto Gain (software)”, default 1, current 1 [1] found control 0x00980913, “Gain”, range 0,255 [1] “Gain”, default 64, current 64 [1] mmap information: [1] frames=4 libv4l2: error allocating conversion buffer [1] Error mapping buffer 0 mmap: Cannot allocate memory libv4l1: error allocating v4l1 buffer: Cannot allocate memory [1] ioctl(VIDIOCGMBUF) - Error device does not support memory map [1] V4L capturing using read is deprecated! [1] Motion only supports mmap. [1] Could not fetch initial image from camera [1] Motion continues using width and height from config file(s) [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 8081 [1] Retrying until successful connection with camera

LD_PRELOAD=/usr/lib/libv4l/v4l2convert.so /usr/bin/motion [0] Processing thread 0 - config file /etc/motion.conf [0] Motion 3.2.11.1 Started [0] Thread 1 is from /etc/motion.conf [1] Thread 1 started [1] cap.driver: “STV06xx” [1] cap.card: “Camera” [1] cap.bus_info: “usb-ar71xx-ehci-1” [1] cap.capabilities=0x05000001 [1] - VIDEO_CAPTURE [1] - READWRITE [1] - STREAMING [1] Supported palettes: [0] motion-httpd/3.2.11.1 running, accepting connections [0] motion-httpd: waiting for data on port TCP 8080 [1] 0: RGB3 (RGB3) [1] 1: BGR3 (BGR3) [1] 2: YU12 (YU12) [1] Selected palette YU12 [1] index_format 8 Test palette YU12 (320×240) [1] Using palette YU12 (320×240) bytesperlines 320 sizeimage 115200 colorspace 00000008 [1] found control 0x00980900, “Brightness”, range 0,31 [1] “Brightness”, default 3, current 3 [1] found control 0x00980901, “Contrast”, range 0,15 [1] “Contrast”, default 11, current 11 [1] found control 0x00980910, “Gamma (software)”, range 500,3000 [1] “Gamma (software)”, default 1000, current 1000 [1] found control 0x00980911, “Exposure”, range 0,1023 [1] “Exposure”, default 256, current 256 [1] found control 0x00980912, “Auto Gain (software)”, range 0,1 [1] “Auto Gain (software)”, default 1, current 1 [1] found control 0x00980913, “Gain”, range 0,255 [1] “Gain”, default 64, current 64 [1] mmap information: [1] frames=4 libv4l2: error allocating conversion buffer [1] Error mapping buffer 0 mmap: Cannot allocate memory [1] Using VIDEO_PALETTE_YUV420P palette [1] Using V4L1 [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 8081 [1] sync error in proc 22284: Invalid argument [1] mcapture error in proc 22284: Invalid argument [1] Video device fatal error - Closing video device [1] Closing video device /dev/video0 [1] Retrying until successful connection with camera

• http://www.lavrsen.dk/foswiki/bin/view/Motion/SupportQuestion2010x05x08x221414
• http://www.lavrsen.dk/foswiki/bin/view/Motion/SupportQuestion2009x01x20x183230

patch : mais tester la version 3.2.12 avant, actuellement 3.2.11.1-1

• http://www.lavrsen.dk/foswiki/bin/view/Motion/Libv4lConvert
• compile de la version actuel
  • a partir du la racine du SDK : svn export svn:svn.openwrt.org/openwrt/packages/multimedia/motion package/motion ===== ping: sendto: Network is unreachable ===== je comprend pas pourquoi mais en configurant l'IP statique j'ai cette erreur . si on configure le routeur en client DHCP , le routeur arrive a se connecter a l'internet <code> IPv4 WAN Status br-lan Type: dhcp Address: 192.168.0.11 Netmask: 255.255.255.0 Gateway: 192.168.0.254 DNS 1: 192.168.0.254 Expires: 23h 46m 51s Connected: 0h 13m 9s </code> c’était les mêmes paramètre en static … le patch accept_ra 1 ne semble pas fonctionner : config interface lan option accept_ra 1