Ci-dessous, les différences entre deux révisions de la page.
Les deux révisions précédentesRévision précédenteProchaine révision | Révision précédente | ||
divers_elec:bme280:bme280 [05/2019] – [BMP280 vs BME280] fred | divers_elec:bme280:bme280 [07/2019] (Version actuelle) – [Temperature accuracy] fred | ||
---|---|---|---|
Ligne 1: | Ligne 1: | ||
+ | ====== choix ====== | ||
+ | |||
+ | * https:// | ||
+ | * http:// | ||
+ | |||
+ | |||
+ | * DHT11 DHT22 AM2302 Temperature Humidity Sensor ? https:// | ||
+ | * DHT22 | ||
+ | * BMP180 Shield | ||
+ | |||
+ | ====== shields ====== | ||
+ | beau tableau explicatif en description | ||
+ | https:// | ||
Ligne 6: | Ligne 19: | ||
{{: | {{: | ||
{{: | {{: | ||
+ | |||
+ | < | ||
+ | 100% brand new and high quality | ||
+ | BME280, the precision sensor from Bosch, is soldered onto PCB. | ||
+ | Not only the pressure and the temperature, | ||
+ | It uses both I2C and SPI (supports 3-, 4-wire SPI) interface | ||
+ | Specifications: | ||
+ | Supply Voltage: 1.8 - 5V DC | ||
+ | Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz) | ||
+ | Operational Range: | ||
+ | Temperature: | ||
+ | Humidity: 0-100% | ||
+ | Pressure: 300-1100 hPa | ||
+ | Resolution: | ||
+ | Temperature: | ||
+ | Humidity: 0.008% | ||
+ | Pressure: 0.18Pa | ||
+ | Accuracy: | ||
+ | Temperature: | ||
+ | Humidity: +-3% | ||
+ | Pressure: +-1Pa | ||
+ | I2C address | ||
+ | SDO LOW : 0x76 | ||
+ | SDO HIGH: 0x77 | ||
+ | </ | ||
+ | |||
+ | ====== driver ====== | ||
+ | * celui de adafruit pour adruino like : https:// | ||
+ | * https:// | ||
+ | * https:// | ||
+ | |||
====== Temperature accuracy ====== | ====== Temperature accuracy ====== | ||
- | * https:// | ||
* https:// | * https:// | ||
* https:// | * https:// | ||
* http:// | * http:// | ||
- | * http:// | ||
* https:// | * https:// | ||
* https:// | * https:// | ||
- | ====== BMP280 vs BME280 ====== | + | < |
+ | mise au point du BME 280 | ||
+ | |||
+ | gris: | ||
+ | DS 23.12*c23.06*c | ||
+ | |||
+ | matin au boot : gris 20,8 Rh29/ | ||
+ | 20.87*c20.94*c | ||
+ | 15 minute plus tard gris 21 Rh27 | ||
+ | 21.75*c21.62*c | ||
+ | |||
+ | |||
+ | pooling 2s : BME en mode force et parasite power pour le 1W | ||
+ | Tgris23,7 | ||
+ | | ||
+ | |||
+ | Gris 23,7 RH 41 | ||
+ | 23.25*c23.19*c | ||
+ | |||
+ | one wire parasite power ne fonctionne pas sur D4 | ||
+ | </ | ||
+ | |||
+ | ====== | ||
https:// | https:// | ||
chip you have send me are not BME280 but BMP280 , there is no humidity available (chip id is 0x58 instead 0x60) the marking on the chip begin with K as written on BMP280 datasheet Page 41. so i ask refund of the order or sending me 3 reals BME280 with marking U as written on BME280 datasheet Page 44. regards | chip you have send me are not BME280 but BMP280 , there is no humidity available (chip id is 0x58 instead 0x60) the marking on the chip begin with K as written on BMP280 datasheet Page 41. so i ask refund of the order or sending me 3 reals BME280 with marking U as written on BME280 datasheet Page 44. regards |